Control Units (ETU/MOSFET)

The Specna Arms HAL electronic control system is designed for replicas with a V3 gearbox. It uses magnetic sensors and allows the replica to be configured in many ways. For correct operation, the new version of the trigger included in the set must be installed.

Features

• Trigger detection with magnetic sensors and Hall effect
• High sensitivity even with light presses
• High durability and resistance to external factors
• Low/high voltage protection
• Overload protection (automatic shutdown above 40 RPS)
• Active brake, binary trigger
• Adjustable trigger sensitivity (5 levels, 20–100%)
• Adjustable pre-cocking (6 levels)
• Programmable auto modes: full auto, semi, 3 or 5 BB burst
• Programmable semi modes: semi, binary, AUG, sniper
• Easy programming from the trigger, low battery alarm
• Compatible with brushless motors (BLDC)

Package Contents

• HAL electronic control system for V3 gearbox
• Trigger tongue
• Mounting kit
• Selector board V3
• Circuit programming card

The Specna Arms HAL electronic control system is designed for replicas with a V2 gearbox. It uses magnetic sensors and allows the replica to be configured in many ways. For correct operation, the new version of the trigger included in the set must be installed.

Features

• Trigger detection with magnetic sensors and Hall effect
• High sensitivity even with light presses
• High durability and resistance to external factors
• Low/high voltage protection
• Overload protection (automatic shutdown above 40 RPS)
• Active brake, binary trigger
• Adjustable trigger sensitivity (5 levels, 20–100%)
• Adjustable pre-cocking (6 levels)
• Programmable auto modes: full auto, semi, 3 or 5 BB burst
• Programmable semi modes: semi, binary, AUG, sniper
• Easy programming from the trigger, low battery alarm
• Compatible with brushless motors (BLDC)

Package Contents

• HAL electronic control system for V2 gearbox
• Trigger tongue
• Mounting kit
• Selector board V2
• Circuit programming card

Specna Arms HAL 2.0 for V2 gearbox is an electronic control system in which the Hall effect trigger offers sensitivity of up to 500 points and is insensitive to dirt and external light. This version contains only the control unit.

With the free Specna Link app you can quickly adjust the replica parameters and create several profiles.

Features

• Trigger sensitivity adjustment
• Pre-cocking for faster response
• Fire modes: single, binary, burst or auto, assigned to the selector positions
• Adjustable burst length and rate of fire
• Protection of Li-Po/Li-Ion batteries against excessive discharge
• Magazine mode
• Real-time battery level display
• Saving settings for different game modes
• Advanced telemetry and continuous monitoring of the replica
• Integrated Bluetooth Low Energy module

Package Contents

• HAL 2.0 control unit
• Trolley/contact not included

The Snow Wolf integrated circuit assembly with BB counter is a replacement part for Snow Wolf M41A series electric airsoft rifles.

Features

• Integrated circuit with BB counter
• Compatible with Snow Wolf M41A series electric rifles

Perun V2 Hybrid replaces the mechanical contacts in the airsoft replica or gel blaster and offers many useful functions. Optical and magnetic sensors eliminate many moving parts prone to failure, and adaptive trigger control allows switching from a very short to a long stroke, even in the field, with almost any trigger, including the original one.

Features

• For V2 gearbox, front wiring
• 5-level adjustable trigger sensitivity, changeable even in the field
• Fire modes programmable independently for both selector positions (safe, semi, burst, auto)
• Active brake against over-rotation (double shot)
• Pre-cocking for fast response, useful in CQB
• 2-stage trigger: semi – burst, semi – auto, burst – auto
• Binary trigger
• Rate of fire reduction
• DMR mode with intervals between semi shots
• Low voltage alarm for Li-Po and Li-Ion
• DSG mode for double sector gear
• Diagnostic system and electronic fuse
• Programming via selector and trigger, with sound signals and multicolor LED

The replacement set contains the sponge and screw for the Leviathan V2 MOSFET. It is useful when reinstalling or servicing the module in the gearbox.

Package Contents

• Replacement sponge
• Replacement screw

Leviathan V3 from Jefftron is a processor-controlled MOSFET with optical sensors and wireless communication, for version 3 gearboxes. It integrates fully into the gearbox in place of the original trigger contacts, and all settings are controlled from the smartphone app (iOS and Android).

Features

• New fire modes, independent for each selector position (safe – semi – auto)
• 3 adjustable bursts (2–20 BBs)
• Rate of fire reducible by up to 40%, with fast trigger response
• Active brake with adjustable intensity (can be disabled)
• Pre-cocking for instant firing in semi
• Adjustable delay between shots (0.1–4.0 s)
• Electronic fuse with adjustable sensitivity
• Low battery indicator for Li-Po 2S–4S and Li-Fe 3S–4S
• Statistics: cycle time, motor consumption, rate of fire, MOSFET temperature
• Multiple settings profiles, firmware updates
• Three shot counters and error log
• Current, voltage and temperature monitoring
• Settings are saved to memory immediately
• Modes: safe, semi, semi/burst, binary, burst, burst+burst, burst/full, full
• Easy installation in V3 gearbox, Tokyo Marui standard
• Optical sensor actuated by the sector gear and optical sensor for the selector
• Real Feel Trigger System (RFTS)

Package Contents

• Leviathan V3 MOSFET
• Trigger not included

The Jefftron II MOSFET is professionally made for electric airsoft replicas (AEG). It increases the rate of fire and extends battery life compared to standard wiring, and pre-soldered wires allow faster installation. Installation should be done by a person experienced in soldering and disassembling replicas.

Features

• Pre-soldered wires: 4 power wires 1.5 mm² (AWG16) with MPPE insulation and 2 signal wires 0.34 mm² (AWG22)
• Conformal-coated board, protected against water
• For springs up to M210
• 6-wire connection
• No current draw at idle
• No sparks at the trigger contacts
• Requires a working cut-off, selector plate, anti-reversal, trigger and trigger lock

Specifications

• Current: 150 A single shot or 50 A burst, max. 30 s
• Batteries up to 17 V (Ni-xx 8.4–12 V, Li-Po 7.4–14.8 V)
• Dimensions: 25 × 12 × 7 mm

Package Contents

• MOSFET with wiring
• Deans T male connector
• 30 A mini fuse
• 4 Faston female terminals 2.8 mm
• 6 black heat-shrink tubes 3.2 mm, length 20 mm
• 3 black heat-shrink tubes 4.8 mm, length 20 mm
• Installation manual in English

Gate X-ASR2 is the newest version of the well-known X-ASR MOSFET. It heats up much less, although it can operate at higher loads, including with M150 springs or stronger. Each time the battery is connected it performs a self-test and signals the operating status and any errors with two LEDs.

Features

• Increased maximum load
• Reduced heating during operation
• LEDs for device status
• Protective conformal coating
• Easy installation, mounted on the connectors
• No reverse polarity protection - be careful when connecting the battery

Package Contents

• X-ASR2
• Debug card
• Connector set

The Gate Warfet power module is an advanced control system for AEG replicas that connects easily to the original wiring via the mini Tamiya adapter. Configuration is done with the tactical programming card, sold separately.

Features

• Third-generation MOSFET
• Configurable fire selector
• Active brake
• Pre-cocking
• ROF control
• Smart trigger
• Battery protection
• Electronic fuse and smart fuse
• Plug & play
• 1–5 BB burst
• Debouncing, built-in self-test, dark mode
• Protective coating, fixed wiring, Dean-T ready
• Compatible with 14.8 V Li-Po

Package Contents

• Warfet power module
• Mini Tamiya adapter for battery
• Mini Tamiya adapter for AEG
• Pair of Dean-T connectors
• Single wire for trigger
• Dual wire for trigger
• Tactical programming card not included

Gate Warfet 1.1 is an advanced control system for AEG replicas. Thanks to the mini Tamiya adapter it connects very easily to the original wiring, and configuration is simple with the included tactical programming card.

Features

• Third-generation MOSFET
• Configurable fire selector
• Active brake
• Pre-cocking
• ROF control
• Smart trigger
• Battery protection
• Electronic fuse and smart fuse
• Plug & play
• 1–5 BB burst
• Debouncing, built-in self-test, dark mode
• Protective coating, fixed wiring, Dean-T ready
• Compatible with 14.8 V Li-Po

Package Contents

• Warfet power module
• Tactical programming card
• Mini Tamiya adapter for battery
• Mini Tamiya adapter for AEG
• Pair of Dean-T connectors
• Single wire for trigger
• Dual wire for trigger
• Quick start guide

Gate USB-Link 2 is a dongle that connects Gate ETU units to PC, Mac and Android devices. Together with the Gate Control Station app it provides full access to the functions and settings of Titan or Aster and allows updating the firmware of the drop-in module and the tactical programming card.

Features

• Connecting Gate ETU to PC, Mac and Android
• Full access to Titan and Aster settings
• Firmware updates

Package Contents

• USB-Link for the GCS app
• USB-C cable (0.6 m)
• Micro-USB cable (0.6 m)
• Debug card
• Quick start guide

The Gate Titan V3 Expert Blu set is designed for version 3 gearboxes with front or rear wiring and includes Expert firmware plus the Blu-Link Bluetooth adapter. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

With the included Blu-Link you can wirelessly manage all settings from the Gate Control Station app; USB-Link is sold separately. The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

Package Contents

• Titan V3 with Expert firmware (rear and front wiring)
• Blu-Link
• Installation kit
• Connector set
• Quick start guides (Titan and Blu-Link)
• Titan patch
• PIN card
• Debug card

Gate Titan V3 Expert is designed for version 3 gearboxes with front or rear wiring and has Expert firmware with all available functions. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

The basic functions are programmed from the trigger, and full configuration is done through Blu-Link or USB-Link (sold separately) and the Gate Control Station app. The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

The Gate Titan V3 Advanced set is designed for version 3 gearboxes with front or rear wiring and includes Advanced firmware together with USB-Link. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

The basic functions are programmed from the trigger, and through USB-Link (included) you have access to advanced settings in the Gate Control Station app; Blu-Link is sold separately. The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

Package Contents

• Titan V3 with Advanced firmware
• USB-Link
• USB-A – micro-USB cable (1.5 m)
• USB-C – micro-USB cable (0.6 m)
• Micro-USB – micro-USB cable (0.6 m)
• Installation kit
• Quick start guides (Titan and Blu-Link)

Gate Titan V2 Expert for NGRS is designed for Tokyo Marui Next Generation (NGRS) gearboxes with rear wiring and has Expert firmware with all available functions. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

The basic functions are programmed from the trigger, and full configuration is done through Blu-Link or USB-Link (sold separately) and the Gate Control Station app. The device should be installed by an experienced technician.

Features

• Compatible with Tokyo Marui Next Generation: M4, SCAR-H, SCAR-L, HK416D, HK416C, HK417
• Not compatible with Tokyo Marui Next Generation: 36C Custom, Model 36K, AKS74N, AKS74U, AK102, AK47 Type 3
• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

Gate Titan V2 Expert for NGRS is designed for Tokyo Marui Next Generation (NGRS) gearboxes with front wiring and has Expert firmware with all available functions. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

The basic functions are programmed from the trigger, and full configuration is done through Blu-Link or USB-Link (sold separately) and the Gate Control Station app. The device should be installed by an experienced technician.

Features

• Compatible with Tokyo Marui Next Generation: M4, SCAR-H, SCAR-L, HK416D, HK416C, HK417
• Not compatible with Tokyo Marui Next Generation: 36C Custom, Model 36K, AKS74N, AKS74U, AK102, AK47 Type 3
• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

Gate Titan V2 Expert is designed for version 2 gearboxes with front wiring and has Expert firmware with all available functions. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

The basic functions are programmed from the trigger, and full configuration is done through Blu-Link or USB-Link (sold separately) and the Gate Control Station app. The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

The Gate Titan V2 Expert Blu set is designed for version 2 gearboxes with rear wiring and includes Expert firmware with all available functions, plus the Blu-Link Bluetooth adapter. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

With the included Blu-Link you can wirelessly manage all settings from the Gate Control Station app; USB-Link is sold separately. The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

Package Contents

• Titan V2 with Expert firmware (rear wiring)
• Blu-Link
• Installation kit
• Connector set
• Quick start guides (Titan and Blu-Link)
• Titan patch
• PIN card
• Debug card

The Gate Titan V2 Expert Blu set is designed for version 2 gearboxes with front wiring and includes Expert firmware with all available functions, plus the Blu-Link Bluetooth adapter. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

With the included Blu-Link you can wirelessly manage all settings from the Gate Control Station app; USB-Link is sold separately. The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

Package Contents

• Titan V2 with Expert firmware (front wiring)
• Blu-Link
• Installation kit
• Connector set
• Quick start guides (Titan and Blu-Link)
• Titan patch
• PIN card
• Debug card

Gate Titan V2 Basic is designed for version 2 gearboxes with front wiring and comes with Basic firmware, which provides the basic functions. Titan is a drop-in MOSFET: an electronic unit that replaces the trigger contacts and the cut-off lever and takes full control of the AEG replica.

The basic functions are programmed from the trigger, and full configuration is done through Blu-Link or USB-Link (sold separately) and the Gate Control Station app. The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po

Package Contents

• Titan V2 with Basic firmware (front wiring)
• Installation kit
• Quick start guides

The Gate Titan V2 Advanced set contains the Titan drop-in MOSFET with Advanced firmware, in the version with rear wiring, together with USB-Link. Titan is an electronic unit that replaces the trigger contacts and the cut-off lever, taking full control of the AEG replica.

The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po
• Programming from the trigger (basic functions), via USB-Link (included) or Blu-Link (sold separately)

Package Contents

• Titan V2 with Advanced firmware (rear wiring)
• USB-Link
• USB-A – micro-USB cable (1.5 m)
• USB-C – micro-USB cable (0.6 m)
• Micro-USB – micro-USB cable (0.6 m)
• Installation kit
• Quick start guides (Titan and Blu-Link)

The Gate Titan V2 Advanced set contains the Titan drop-in MOSFET with Advanced firmware, in the version with front wiring, together with USB-Link. Titan is an electronic unit that replaces the trigger contacts and the cut-off lever, taking full control of the AEG replica.

The device should be installed by an experienced technician.

Features

• Third-generation MOSFET
• Trigger sensitivity adjustment
• Configurable fire selector
• Adaptive active brake
• Cycle detection, pre-cocking
• ROF control and stabilization
• Sniper delay, smart trigger, AUG mode, equalizer
• Battery protection and low battery warning
• Electronic fuse and smart fuse
• 1–5 BB burst, debouncing, built-in self-test, dark mode
• Fixed wiring, Dean-T ready, mini-Tamiya adapter
• Compatible with 14.8 V Li-Po
• Programming from the trigger (basic functions), via USB-Link (included) or Blu-Link (sold separately)

Package Contents

• Titan V2 with Advanced firmware (front wiring)
• USB-Link
• USB-A – micro-USB cable (1.5 m)
• USB-C – micro-USB cable (0.6 m)
• Micro-USB – micro-USB cable (0.6 m)
• Installation kit
• Quick start guides (Titan and Blu-Link)

Gate Titan II Bluetooth is the flagship Gate electronic trigger unit (ETU) for V2 gearboxes, in the version for HPA systems with rear wiring and Expert firmware. The optical trigger sensor and the innovative gear sensor provide extremely precise control of every cycle.

Features

• Expert firmware
• For V2 gearbox, rear wiring, HPA
• Integrated Bluetooth 5.2: direct access to settings, telemetry, smartwatch, Statum and other Gate devices
• Patented gear sensor that detects every tooth and the direction of rotation, for very precise cycle control
• Optical trigger sensor: up to 50 sensitivity levels in the first millimeter
• Mechanical protection of the trigger sensors
• Ultra-precise telemetry thanks to the new current sensor
• Pre-cocking adjustable in percentages
• Built-in voltage boost converter, trouble-free operation at low temperatures
• Programmable multifunction port: tracer and sensors in the hop-up chamber, bolt-catch button, single solenoid HPA engine, electric magazine, magazine sensor, flashlight
• GCS app for iOS, Android, macOS, Windows, watchOS, Wear OS
• Deep sleep mode with consumption of only 0.1 mA

Gate Titan II Bluetooth is the flagship Gate electronic trigger unit (ETU) for V2 gearboxes, in the version for HPA systems with front wiring and Expert firmware. The optical trigger sensor and the innovative gear sensor provide extremely precise control of every cycle.

Features

• Expert firmware
• For V2 gearbox, front wiring, HPA
• Integrated Bluetooth 5.2: direct access to settings, telemetry, smartwatch, Statum and other Gate devices
• Patented gear sensor that detects every tooth and the direction of rotation, for very precise cycle control
• Optical trigger sensor: up to 50 sensitivity levels in the first millimeter
• Mechanical protection of the trigger sensors
• Ultra-precise telemetry thanks to the new current sensor
• Pre-cocking adjustable in percentages
• Built-in voltage boost converter, trouble-free operation at low temperatures
• Programmable multifunction port: tracer and sensors in the hop-up chamber, bolt-catch button, single solenoid HPA engine, electric magazine, magazine sensor, flashlight
• GCS app for iOS, Android, macOS, Windows, watchOS, Wear OS
• Deep sleep mode with consumption of only 0.1 mA

Gate Titan II Bluetooth is the flagship Gate electronic trigger unit (ETU) for V2 gearboxes, in the version for AEG replicas with rear wiring and Expert firmware. The optical trigger sensor and the innovative gear sensor provide extremely precise control of every cycle.

Features

• Expert firmware
• For V2 gearbox, rear wiring, AEG
• Integrated Bluetooth 5.2: direct access to settings, telemetry, smartwatch, Statum and other Gate devices
• Patented gear sensor that detects every tooth and the direction of rotation, for very precise cycle control
• Optical trigger sensor: up to 50 sensitivity levels in the first millimeter
• Mechanical protection of the trigger sensors
• Ultra-precise telemetry thanks to the new current sensor
• Pre-cocking adjustable in percentages
• Built-in voltage boost converter, trouble-free operation at low temperatures
• Programmable multifunction port: tracer and sensors in the hop-up chamber, bolt-catch button, single solenoid HPA engine, electric magazine, magazine sensor, flashlight
• GCS app for iOS, Android, macOS, Windows, watchOS, Wear OS
• Deep sleep mode with consumption of only 0.1 mA

Gate Titan II Bluetooth is the flagship Gate electronic trigger unit (ETU) for V2 gearboxes, in the version for AEG replicas with front wiring and Expert firmware. The optical trigger sensor and the innovative gear sensor provide extremely precise control of every cycle.

Features

• Expert firmware
• For V2 gearbox, front wiring, AEG
• Integrated Bluetooth 5.2: direct access to settings, telemetry, smartwatch, Statum and other Gate devices
• Patented gear sensor that detects every tooth and the direction of rotation, for very precise cycle control
• Optical trigger sensor: up to 50 sensitivity levels in the first millimeter
• Mechanical protection of the trigger sensors
• Ultra-precise telemetry thanks to the new current sensor
• Pre-cocking adjustable in percentages
• Built-in voltage boost converter, trouble-free operation at low temperatures
• Programmable multifunction port: tracer and sensors in the hop-up chamber, bolt-catch button, single solenoid HPA engine, electric magazine, magazine sensor, flashlight
• GCS app for iOS, Android, macOS, Windows, watchOS, Wear OS
• Deep sleep mode with consumption of only 0.1 mA

The Gate Statum tactical computer mounts on the replica and connects to the electronic trigger unit, displaying all important data in real time: remaining BBs, battery level, fire mode and more.

Features

• Connects to the replica electronic trigger units for complete real-time data
• 128 × 128 px OLED display with adjustable brightness
• Polycarbonate window coated with 3mk FlexibleGlass
• CNC-machined 7075 aluminum body, IP68 water and dust resistant, MIL-STD-810H standard
• Mounts on standard 20 mm rails
• 3-axis accelerometer and gyroscope
• Bluetooth 5.0 connection
• 850 mAh Li-Po battery, USB-C port
• 4 customizable dashboards
• Functions: remaining BB counter, AEG battery level, estimated remaining shots, magazine counter, tilt indicator, bolt-catch reset, temperature, distance/pedometer/calories, fire mode notification, mission/respawn timer
• Compatible with Titan V2 / V2 NGRS / V3, Aster V2 / V3, Blu-Link, Basic / Advanced / Expert firmware; not compatible with GCS PC/Mac 2.x and basic MOSFETs

Specifications

• Dimensions: 47 × 60 × 54 mm
• Weight: 180 g
• Color: black

The Gate Statum tactical computer mounts on the replica and connects to the electronic trigger unit, displaying all important data in real time: remaining BBs, battery level, fire mode and more.

Features

• Connects to the replica electronic trigger units for complete real-time data
• 128 × 128 px OLED display with adjustable brightness
• Polycarbonate window coated with 3mk FlexibleGlass
• CNC-machined 7075 aluminum body, IP68 water and dust resistant, MIL-STD-810H standard
• Mounts on standard 20 mm rails
• 3-axis accelerometer and gyroscope
• Bluetooth 5.0 connection
• 850 mAh Li-Po battery, USB-C port
• 4 customizable dashboards
• Functions: remaining BB counter, AEG battery level, estimated remaining shots, magazine counter, tilt indicator, bolt-catch reset, temperature, distance/pedometer/calories, fire mode notification, mission/respawn timer
• Compatible with Titan V2 / V2 NGRS / V3, Aster V2 / V3, Blu-Link, Basic / Advanced / Expert firmware; not compatible with GCS PC/Mac 2.x and basic MOSFETs

Specifications

• Dimensions: 47 × 60 × 54 mm
• Weight: 180 g
• Color: dark earth

The Gate Statum tactical computer mounts on the replica and connects to the electronic trigger unit, displaying all important data in real time: remaining BBs, battery level, fire mode and more. The set also includes the Blu-Link adapter.

Features

• Connects to the replica electronic trigger units for complete real-time data
• 128 × 128 px OLED display with adjustable brightness
• Polycarbonate window coated with 3mk FlexibleGlass
• CNC-machined 7075 aluminum body, IP68 water and dust resistant, MIL-STD-810H standard
• Mounts on standard 20 mm rails
• 3-axis accelerometer and gyroscope
• Bluetooth 5.0 connection
• 850 mAh Li-Po battery, USB-C port
• 4 customizable dashboards
• Functions: remaining BB counter, AEG battery level, estimated remaining shots, magazine counter, tilt indicator, bolt-catch reset, temperature, distance/pedometer/calories, fire mode notification, mission/respawn timer
• Compatible with Titan V2 / V2 NGRS / V3, Aster V2 / V3, Blu-Link, Basic / Advanced / Expert firmware; not compatible with GCS PC/Mac 2.x and basic MOSFETs

Specifications

• Dimensions: 47 × 60 × 54 mm
• Weight: 180 g
• Color: black

Package Contents

• Statum tactical computer
• Blu-Link adapter

The Gate Statum tactical computer mounts on the replica and connects to the electronic trigger unit, displaying all important data in real time: remaining BBs, battery level, fire mode and more. The set also includes the Blu-Link adapter.

Features

• Connects to the replica electronic trigger units for complete real-time data
• 128 × 128 px OLED display with adjustable brightness
• Polycarbonate window coated with 3mk FlexibleGlass
• CNC-machined 7075 aluminum body, IP68 water and dust resistant, MIL-STD-810H standard
• Mounts on standard 20 mm rails
• 3-axis accelerometer and gyroscope
• Bluetooth 5.0 connection
• 850 mAh Li-Po battery, USB-C port
• 4 customizable dashboards
• Functions: remaining BB counter, AEG battery level, estimated remaining shots, magazine counter, tilt indicator, bolt-catch reset, temperature, distance/pedometer/calories, fire mode notification, mission/respawn timer
• Compatible with Titan V2 / V2 NGRS / V3, Aster V2 / V3, Blu-Link, Basic / Advanced / Expert firmware; not compatible with GCS PC/Mac 2.x and basic MOSFETs

Specifications

• Dimensions: 47 × 60 × 54 mm
• Weight: 180 g
• Color: dark earth

Package Contents

• Statum tactical computer
• Blu-Link adapter

The Gate programming button allows configuration of Gate MERF 3.2 and NanoHARD controllers. It is a useful accessory if you have lost the original button or want a spare.

Features

• Compatible with Gate MERF 3.2 and NanoHARD

Gate PicoSSR 3 is the smallest advanced AEG control system in the world, very powerful despite its small size. Heat-shrink tubes protect it against adverse weather conditions.

Features

• Third-generation MOSFET
• Fixed wiring
• Weather resistant thanks to heat-shrink tubes
• Not compatible with micro-switches

Specifications

• Dimensions: 4 × 6 × 21 mm
• Maximum nominal battery voltage: 12.8 V

Package Contents

• PicoSSR 3
• 2 single signal wires for trigger contacts, 60 cm each
• 3 heat-shrink tubes

Gate PicoAAB is the smallest third-generation MOSFET with an active brake in the Gate range. It protects the trigger contacts, and the active brake quickly stops the motor after each cycle.

Features

• Third-generation MOSFET
• Active brake
• Electronic fuse
• Debouncing
• Protective coating
• Fixed wiring
• Compatible with 14.8 V Li-Po

Package Contents

• PicoAAB MOSFET
• Single signal wire for trigger contacts
• Dual signal wire for trigger contacts
• 2.8 × 0.8 mm male terminal with red heat-shrink tube (battery plus)
• 2.8 × 0.5 mm male terminal with black heat-shrink tube (motor minus)
• 2.8 × 0.5 mm male terminal with red heat-shrink tube (motor plus)
• 2.8 × 0.5 mm female terminal with thin black heat-shrink tube (battery minus)

Gate MERF 3.2 is an advanced control system for AEG replicas, a third-generation MOSFET with a configurable fire selector and active brake. It installs plug & play and protects both the contacts and the battery.

Features

• Third-generation MOSFET
• Configurable fire selector
• Active brake
• ROF control
• Smart trigger
• Battery protection
• Electronic fuse
• Plug & play
• 3 BB burst
• Debouncing
• Protective coating
• Fixed wiring, Dean-T ready

Package Contents

• MERF 3.2
• Additional Dean-T connector kit
• Single signal wire for trigger contacts
• Dual signal wire for trigger contacts
• Programming button

Gate Blu-Link enables wireless management of Gate ETU units through the Gate Control Station app for iOS, Android, Windows and macOS. You can control Aster or Titan from your phone or computer and connect them with other compatible Gate devices, such as the Statum computer mounted on the weapon.

In addition to the Bluetooth 5.0 function, Blu-Link acts as an extra safety fuse and a multifunction wattmeter for constant monitoring of the replica status.

Features

• Bluetooth adapter
• Wireless connection between Gate ETU and compatible Gate devices
• Compatible with the GCS app for iOS, Android and Windows/macOS
• Switching between data transfer mode and firing mode from the app
• Additional configurable smart fuse (UVP, SCP, OCP, OTP)
• Multifunction wattmeter for reading telemetry data
• MIL-V-173C coating
• Very low power consumption
• Can stay connected between the ETU and the battery throughout the game
• Allows programming, changing settings and updating the firmware of Titan and Aster

Gate Aster V3 SE Expert is an ETU/MOSFET for version 3 gearboxes with Expert firmware and an excellent balance of features and performance. Trigger sensitivity can be set right out of the box, from "hair trigger" to the full stroke, and the main functions are programmed from the trigger and selector.

The smart fuse protects the battery, motor and controller, including when the battery is connected in reverse, and advanced settings are available through Blu-Link or USB-Link and the GCS app.

Features

• Expert firmware
• Battery reverse polarity protection
• Proximity sensor for the trigger, up to 315 sensitivity settings
• Configuration via the trigger or via Blu-Link/USB-Link and the GCS app
• Built-in RGB LED for easy programming
• No modification of the gearbox shell required
• Optical sensors instead of mechanical contacts
• Optical sensor compatible with infinite torque-up, DSG, SSG, 19-tooth and standard gears
• Automatic pre-cocking (low, mid, high), adaptive active brake, safe – semi – binary selector mode
• Support for brushless motors and heavily modified AEGs
• MIL-V-173C coating

Specifications

• Supply voltage: 3.75–12.9 V (1.2 V during firing)

Gate Aster V3 SE is an ETU/MOSFET for version 3 gearboxes with an excellent balance of features and performance. Trigger sensitivity can be set right out of the box, from "hair trigger" to the full stroke, and the main functions are programmed from the trigger and selector.

The smart fuse protects the battery, motor and controller, including when the battery is connected in reverse, while optical sensors replace mechanical contacts that are prone to failure.

Features

• Battery reverse polarity protection
• Proximity sensor for the trigger, up to 315 sensitivity settings
• Configuration via the trigger or via Blu-Link/USB-Link and the GCS app
• Built-in RGB LED for easy programming
• No modification of the gearbox shell required
• Optical sensor compatible with infinite torque-up, DSG, SSG, 19-tooth and standard gears
• Automatic pre-cocking (low, mid, high), adaptive active brake
• Binary trigger as a basic function, brushless motor support
• MIL-V-173C coating

Specifications

• Supply voltage: 3.75–12.9 V (1.2 V during firing)
• Current consumption: 26 mA
• Low-power mode: 285 μA
• Dimensions: 73.5 × 24 × 12.5 mm
• Weight: 26 g
• Operating temperature: -15°C … +50°C
• Relative humidity: ≤ 80%

Gate Aster II Bluetooth Expert for V3 gearboxes brings new features to all replicas with a version 3 gearbox, both AEG and HPA with dual solenoid. Through Bluetooth 5.2 you get direct access to settings, telemetry and extended functions in the GCS app for phone and smartwatch.

The AEG version works with brushed and brushless motors, even at 11.1 V, and in HPA, single or dual solenoid engines can be connected.

Features

• Bluetooth 5.2, Expert firmware
• Trigger sensitivity adjustment (up to 35 levels in the first millimeter)
• Automatic pre-cocking
• Active brake with adaptive mode
• Binary trigger
• Compatible with brushless motors, even at 11.1 V
• The Aster fuse protects the motor, battery and controller
• Highly reliable optical sensors
• Weather-resistant MIL-V-173C coating
• Free online firmware updates
• Low power consumption
• Compatible with dual solenoid HPA engines: Pulsar D, PolarStar F2
• Compatible with single solenoid HPA engines: Pulsar H, Pulsar S, Wolverine Inferno Gen 2, Wolverine Reaper, PolarStar Jack, Redline N7

Package Contents

• Aster II Bluetooth MOSFET for V3
• Cables for single or dual solenoid are not included

The G&G set contains the ETU and MOSFET modules for version II G2H gearboxes, together with a 16AWG cable set.

Features

• ETU and MOSFET modules for ver. II G2H gearbox
• 16AWG cables

Package Contents

• ETU and MOSFET modules
• 16AWG cable set